Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
12/08/05 14:28
Read: times


 		 #104885 - Correct Freq.
Responding to: ???'s previous message
At present I am using 6MHz clock for HCTL2032. I am running my steppers at 60RPM and encoder is 500PPR. What frequency is suitable for this application. Is 6MHz slow.

Thanks & Regards,
Prahlad Purohit

List of 63 messages in thread
TopicAuthorDate
shaft encoder & HCTL2032 with stepper.            01/01/70 00:00      
   2032 clock            01/01/70 00:00      
      Re: 2032 Clock.            01/01/70 00:00      
   Correct Freq.            01/01/70 00:00      
      discusses the clocking            01/01/70 00:00      
         and one more            01/01/70 00:00      
   Clock = 32MHz still decoder cheating.            01/01/70 00:00      
      Damper ?            01/01/70 00:00      
         Re: Damper.            01/01/70 00:00      
            Sp            01/01/70 00:00      
               Re: Sp.            01/01/70 00:00      
                  closed loop systems            01/01/70 00:00      
                     and            01/01/70 00:00      
                  What is the reason for vibration?            01/01/70 00:00      
                     Re: Vibration Source.            01/01/70 00:00      
                        Vibration or resonance..?            01/01/70 00:00      
                           Stepper motor action            01/01/70 00:00      
                              Exactly...            01/01/70 00:00      
                                 OK            01/01/70 00:00      
                                    ringing            01/01/70 00:00      
                                       depends on factors            01/01/70 00:00      
                                       Just visualize any mechanical drive stop            01/01/70 00:00      
                        Possible tests            01/01/70 00:00      
                           Bummer isn't it ?            01/01/70 00:00      
      I know this, but has not seen it with tr            01/01/70 00:00      
         lower the clock            01/01/70 00:00      
            exactly            01/01/70 00:00      
               Re: Exactly.            01/01/70 00:00      
      errors            01/01/70 00:00      
         oscillation            01/01/70 00:00      
   Not Sure.            01/01/70 00:00      
      what does the scope say?            01/01/70 00:00      
         oscillator            01/01/70 00:00      
   Tried Frequencies from 25kHz to 33MHz.            01/01/70 00:00      
      you have something defective            01/01/70 00:00      
         Mechanics            01/01/70 00:00      
            I agree            01/01/70 00:00      
               any mechab=nical, however bad should giv            01/01/70 00:00      
                  Sloppy            01/01/70 00:00      
         RE: defective.            01/01/70 00:00      
            did you forget the mistletoe?            01/01/70 00:00      
               Re: offload.            01/01/70 00:00      
                  I mixed up 2 HCTLxxx chips.            01/01/70 00:00      
   Why encoder?            01/01/70 00:00      
      Reference            01/01/70 00:00      
         absolute encoder            01/01/70 00:00      
            expensive.            01/01/70 00:00      
               absolute encoders            01/01/70 00:00      
               the real problem with absolute encoders            01/01/70 00:00      
                  Nah            01/01/70 00:00      
      Re: Why Encoder.            01/01/70 00:00      
   Encoder with stepper            01/01/70 00:00      
   Problem Solved.            01/01/70 00:00      
      "Solved" ?            01/01/70 00:00      
         Re: Resonance.            01/01/70 00:00      
      "problem solved" does not jive            01/01/70 00:00      
         Re: Misleading encoder.            01/01/70 00:00      
            HCTL-2032 encoder counting problem            01/01/70 00:00      
   Torsion Damper.            01/01/70 00:00      
      Capture ?            01/01/70 00:00      
         Stepper motor with shaft encoder            01/01/70 00:00      
         Re: Capture.            01/01/70 00:00      
   Stepper motor            01/01/70 00:00      

Back to Subject List