Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
07/29/05 11:48
Modified:
  07/29/05 12:24
Read: times


 		 #98437 - Simon says
Responding to: ???'s previous message
I dont need to measure the currrent but I am worried that large currents from the test supply (300A) might flow into my low current control cct. I think that im not "the sharpest tool in the shed", maybe that is why i dont understand this problem.
(Georg) Simon (Ohm) says that to get "large currents .. [to] flow into" you need high voltage or low resistance.
So, since the voltage is given (10V) and I am sure you will have a reasonable Rin to your Op-Amps.
Thus, no worry

Erik

Ps "simon says" is a popular parlor game in the US



List of 59 messages in thread
TopicAuthorDate
Op amp input, high voltage measurement            01/01/70 00:00      
   You need...            01/01/70 00:00      
   ISO106, and: BE CAREFUL!!            01/01/70 00:00      
      Very dangerous indeed!!!!!!            01/01/70 00:00      
         Oh dear...            01/01/70 00:00      
            thanks guys, & Mahmood, my condolences            01/01/70 00:00      
               a question for Kai....            01/01/70 00:00      
                  Answer            01/01/70 00:00      
                     Precision            01/01/70 00:00      
                        I'd say that the DC "current transformer            01/01/70 00:00      
                           Not            01/01/70 00:00      
         Condolences            01/01/70 00:00      
         Condolences            01/01/70 00:00      
         busbars            01/01/70 00:00      
            Thank you all            01/01/70 00:00      
   Isolation transformer            01/01/70 00:00      
      DC            01/01/70 00:00      
         maybe this is what a "DC current transfo            01/01/70 00:00      
   High Voltage Op Amps            01/01/70 00:00      
   Problem Change, change in supply values            01/01/70 00:00      
      INA117 is a good choice then            01/01/70 00:00      
         shunt resistor            01/01/70 00:00      
            Thick piece of wire            01/01/70 00:00      
               fine if you can calibrate.            01/01/70 00:00      
                  Yes            01/01/70 00:00      
               Piece of Wire.            01/01/70 00:00      
            Nevertheless...            01/01/70 00:00      
               Try these            01/01/70 00:00      
            Shunt Resistors            01/01/70 00:00      
   change in problem - different supply val            01/01/70 00:00      
   The application..........sorry its late            01/01/70 00:00      
      Not really            01/01/70 00:00      
      More questions...            01/01/70 00:00      
         Answers.......I hope this is clearer            01/01/70 00:00      
            I smell smoke            01/01/70 00:00      
               Toasty warm            01/01/70 00:00      
            Volt range            01/01/70 00:00      
               welder voltage            01/01/70 00:00      
                  Extremely informative!            01/01/70 00:00      
                     So...            01/01/70 00:00      
                        ahm confoosed            01/01/70 00:00      
                           millivolts            01/01/70 00:00      
      Simon says            01/01/70 00:00      
         So the aim is to test for shorted turns?            01/01/70 00:00      
            I doubt this will work with DC motors            01/01/70 00:00      
   Ring Counter theory and schematic            01/01/70 00:00      
      Spot on Charles            01/01/70 00:00      
   millivolts and growler test            01/01/70 00:00      
   Test readings            01/01/70 00:00      
      Shorted turn            01/01/70 00:00      
      Could you draw a scheme?            01/01/70 00:00      
         Windings            01/01/70 00:00      
            I'm a bloody amateur...            01/01/70 00:00      
      Where you are measuring            01/01/70 00:00      
         Big fault ?            01/01/70 00:00      
            shorted turn            01/01/70 00:00      
               Update            01/01/70 00:00      
   Latest update            01/01/70 00:00      
      Much much more details needed!            01/01/70 00:00      

Back to Subject List