Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
01/27/06 15:38
Read: times


 		 #108522 - More cheap ARMs
Responding to: ???'s previous message
Alexander Finch said:
That cheap ARM board looks good but the uC is soldered on. For this application, I'll be intergrating into a PCB design, so I'm looking for the device by itself (which presumably would be cheaper yet..).

Take a look at these - for twenty & thirty quid:

http://www.mivation.com/armheader.htm

They say all the processor pins are available on the headers - so just pop it on your PCB!

More stuff here:

http://www.mivation.com/armproto.htm

Better stop now, before I get flamed for turning this into an ARM forum...! :-0

List of 43 messages in thread
TopicAuthorDate
Starting with uControllers            01/01/70 00:00      
   Phew            01/01/70 00:00      
   starting            01/01/70 00:00      
      yeah, deep water..            01/01/70 00:00      
         And Sarks too!            01/01/70 00:00      
            ARMs not costing an arm & a leg!            01/01/70 00:00      
               true, but            01/01/70 00:00      
                  try a simulation            01/01/70 00:00      
                  Calculation            01/01/70 00:00      
                  More cheap ARMs            01/01/70 00:00      
         bad worker always blames his tools            01/01/70 00:00      
            I could blame "the tools"            01/01/70 00:00      
            Well            01/01/70 00:00      
               Hmm...            01/01/70 00:00      
                  Consultants of the world - unite!            01/01/70 00:00      
                     well, the way I heard it was ...            01/01/70 00:00      
   AT89S52            01/01/70 00:00      
   notwithstanding what others have said            01/01/70 00:00      
   For RS232 check this out            01/01/70 00:00      
   Ok, after much learning...            01/01/70 00:00      
      bye            01/01/70 00:00      
      bye            01/01/70 00:00      
         AVR            01/01/70 00:00      
   What are your requirements?            01/01/70 00:00      
   What are your requirements?            01/01/70 00:00      
   guide to microcontroller selection            01/01/70 00:00      
      it would be nice            01/01/70 00:00      
         Direct link            01/01/70 00:00      
         pdf 1.5            01/01/70 00:00      
            I have adobe 6.0 standard            01/01/70 00:00      
               me too, and I had no trouble with it ...            01/01/70 00:00      
                  Upgrade to 7            01/01/70 00:00      
                     upgrade???            01/01/70 00:00      
                        but ... you said you were using v6 ...            01/01/70 00:00      
                           where?            01/01/70 00:00      
                              your post on 1/26 says that, doesn't it?            01/01/70 00:00      
                                 Version ?            01/01/70 00:00      
                                 got two discussions mixed up            01/01/70 00:00      
                        No way            01/01/70 00:00      
   farnell.com            01/01/70 00:00      
      Farnell            01/01/70 00:00      
      it's like saying they sell parts            01/01/70 00:00      
   You've got to size the task.            01/01/70 00:00      

Back to Subject List