Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
01/23/06 16:39
Read: times


 		 #108103 - ARMs not costing an arm & a leg!
Responding to: ???'s previous message
Ian Bell said:
If you are doing any kind of image recognition you won't be using an 8051.

Yes - I'd tend to agree with that!

Pick something like an ARM and buy a single board development kit for it. You'll get a free demo C compiler for it and if your program turns out to exceed the demo limits there are free gcc tools you can use instead. Check out the Philips web site.

Cheap ARM units:

http://www.8052.com/forumchat/read.phtml?id=107945


List of 43 messages in thread
TopicAuthorDate
Starting with uControllers            01/01/70 00:00      
   Phew            01/01/70 00:00      
   starting            01/01/70 00:00      
      yeah, deep water..            01/01/70 00:00      
         And Sarks too!            01/01/70 00:00      
            ARMs not costing an arm & a leg!            01/01/70 00:00      
               true, but            01/01/70 00:00      
                  try a simulation            01/01/70 00:00      
                  Calculation            01/01/70 00:00      
                  More cheap ARMs            01/01/70 00:00      
         bad worker always blames his tools            01/01/70 00:00      
            I could blame "the tools"            01/01/70 00:00      
            Well            01/01/70 00:00      
               Hmm...            01/01/70 00:00      
                  Consultants of the world - unite!            01/01/70 00:00      
                     well, the way I heard it was ...            01/01/70 00:00      
   AT89S52            01/01/70 00:00      
   notwithstanding what others have said            01/01/70 00:00      
   For RS232 check this out            01/01/70 00:00      
   Ok, after much learning...            01/01/70 00:00      
      bye            01/01/70 00:00      
      bye            01/01/70 00:00      
         AVR            01/01/70 00:00      
   What are your requirements?            01/01/70 00:00      
   What are your requirements?            01/01/70 00:00      
   guide to microcontroller selection            01/01/70 00:00      
      it would be nice            01/01/70 00:00      
         Direct link            01/01/70 00:00      
         pdf 1.5            01/01/70 00:00      
            I have adobe 6.0 standard            01/01/70 00:00      
               me too, and I had no trouble with it ...            01/01/70 00:00      
                  Upgrade to 7            01/01/70 00:00      
                     upgrade???            01/01/70 00:00      
                        but ... you said you were using v6 ...            01/01/70 00:00      
                           where?            01/01/70 00:00      
                              your post on 1/26 says that, doesn't it?            01/01/70 00:00      
                                 Version ?            01/01/70 00:00      
                                 got two discussions mixed up            01/01/70 00:00      
                        No way            01/01/70 00:00      
   farnell.com            01/01/70 00:00      
      Farnell            01/01/70 00:00      
      it's like saying they sell parts            01/01/70 00:00      
   You've got to size the task.            01/01/70 00:00      

Back to Subject List